Reviews

One of the only steel bumpers with an actual place for the tag to go!! Great bumper!

These are not your average running boards! Definitely enhances the look of your vehicle. Great quality! Hubs installed in about an hour. Love them!

Everything was packed with blown foam around the parts and delivery still managed to break one of the 25w light brackets. I ll be calling Hooke to try and buy a replacement. The parts went together perfectly. FYI, when bolting together the 3 bolts that hold the sides to the center, make sure you tighten the top bolt because it’s close to impossible to get back to. I did cut the ends of each bumper side and bent them further in to get completely under the fender. I rewelded them. Sanded them and painted with bed liner in those 4 spots and you would have to be told where to look to see it. I am very happy with the fit of the bumper and it looks amazing on the truck. It takes two people to mount if you are installing a winch with it. The steel was plenty thick enough to weld back up. I highly recommend Hooke Road.

Excellent made running board the only thing I don't understand is why the steps are offset from the door entrance I have to actually step on the tube to get in the jeep You're not on the 1941 logo step plates. They lineup great with the doors off for your foot to sit on them LOL

Sturdy metal, you can tell it’s not some cheap rack with 1/8th inch tubing. Lights on the side came pre-installed and they’re bright! Light pods are fairly bright as well. The kit was easy to install I would recommend taking it to a certified installer if you’re afraid to drill into the cab.

Sturdy, very easy install, you will have to cut fenders, but if you are this far in, you should anyways!
Reason for the -1 star: some of the welds were less than pleasing(probably going to have to re-weld several spots, ill see after preliminary testing) & came with pretty random hardware, not even enough of the same pieces to mount it. I had to use old hardware.

Great rack for the money- super strong and heavy duty. Took about 2.5 hours to do by myself (in hindsight I could have used some help lifting sections up). I was worried about it being noisy but took it on an 80 mile trip today averaging 75mph and really didn’t notice much increase in wind noise

Love it!! I can get in my Bronco a lot easier!!

This bumper is good quality and easy to install. It’s definitely durable. Love the swing outs. The only downside fall is the latches bag down lower than I would like.

I color matched the fender pieces the better blend it in. I would get into this over buying another OEM bumper.

THE FITMENT IS ROUGH! This is about all the play you are going to get but it is still noticeably off.

This bumper looks great on my truck and was very easy to install. The fit is very precise and matches up to the body lines.

Nice heavy duty bumper compared to stock. Easy to install, just be ready for sensors are held in a bit different and spare jack you don’t need the ring clip anymore. My only complaint is I wish the mount was closer to the factory mount style. I think it’s still plenty strong, but I feel the factory mount would be stronger with this bumper. Still a 5 star for me!!

The bumper itself was very well made, packaging was excellent and arrived without a scratch. Fit and finish great. And all of the hardware was actually there. But the customer service response to questions was faster than expected and the reply’s were just as fast and helpful. Will purchase their products again

I did a ton of research looking for a sturdy bumper for a price range that wouldn't break the bank, and Hooke really knocked it out of the park. Instructions were included but could use some work on some parts as I had some doubts on what I was doing following some steps. I still managed but overall, it fits great! Sure there were some chips here and there, but I know this bumper is to keep my truck safer so I didn't care as rock chips and some scrapes will happen over time. The look is awesome too, the only thing I did wish for this bumper was for it to be lighter, but again, Hooke included the weight so I knew what I was getting.

Installation wasn't bad,when removing the stock aluminum.bumper,their are 2 wings riveted to the ends,this is bolted to the edge ,under the fog light.Drill the rivets out of one side,front bumper will pull right out.Loosly attach the winch bracket,with the two bolts,then put bumper on,and tighten down,wrench and 3/8"socket& ratchet will do the job,from underneath.Waiting on winch, and light switch& harness, so no comment on that end yet.Bumper fit well,and seems well built.

Fitment was great and they look really good. Gained alot of clearance in the wheel well now. And moved up from 35's to 37's and could even go with 40's on a 3.5" lift

Ordered this rear bumper a few weeks ago for my 2020JL. It fits well on the frame and looks great. Unfortunately when I tried to close the tailgate with the stock spare on it, it wouldn't close so I removed the spare until I can get some spacers for it. Installing the rear plate light was a breeze, but I didn't install the pod lights yet, as I plan to operate them on their own separate switch.

Absolutely love how beefier my truck looks. Took me and my dad about 3 hours for removal and install.

I now own the Tailgate Basket Rear Cargo Rack w/ Reinforced Tailgate Hinge Kit for my 2013 Jeep Wrangler JK, the interior rear cargo rack which has already proven so useful and the HR roof rack to truly utilize all my space. I’ve used all three recently on a camping trip and they did not disappoint. Thanks y’all.

Gave my jeep a warrior look

Quick shipping, box was damaged from shippers, D loops missing, bull bar is attached with 2 little bolts. But is still better that the uj flat bumper, winch fits nice.

I bought the rear inner fenders for my JK to clean up the appearance and for added protection. I love em. They look great and fit perfectly. I highly recommend them.

Replaced 2016 JK OEM chrome runners. Fast delivery. Packed well, no damage. Fit up perfect. 4 nuts/side n done...easy install. I added flat washers to the Jeep stock nuts, cuz holes on running boards are slightly large. Lowers my step up by a helpful 4" vs OEM chrome brds. Very sturdy, good quality product, clear instructions. Highly recommend Hooke Rd!

I was a little skeptical at first ordering these doors for the price but I must say I am pleasantly surprised, they are pretty heavy duty and well made with a nice rugged coating. They took about an hour of assembly and adjustment to get the fit tight but it was not difficult in the least

Rack is great and easy to install. Also, customer service was great when I originally ordered the wrong item. Thank you